Renault Megane, Scenic

Since 1996 of release

Repair and car operation



Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
+ Engine repair
+ System of cooling, heating
- Power supply systems, release
   + Fuel and an exhaust system - petrol models
   - Fuel and exhaust systems - diesel models
      Removal and installation of a casing of the air filter
      Removal and installation of the gauge of a stock of fuel
      Removal and installation of a fuel tank
      Removal, installation and adjustment of a rope of gas
      Removal and installation of a pedal of gas
      Pouring and prorolling of fuel system
      Check and adjustment of the maximum turns of the engine
      Removal, installation, check and adjustment of a thermodrive and rope of fast idling
      Removal, installation, check and adjustment of components of system of fast idling
      Check, removal and installation of the proof-reader of the moment of injection at cold start
      The description, removal and valve installation отсечки fuel
      Removal and installation of the gauge of temperature of fuel
      Removal and installation of the fuel pump
      Methods of check and adjustment of the moment of injection
      Check and adjustment of the moment of injection
      Check, removal and installation of atomizers
      Removal and installation of the inlet pipeline and final collector
      Check and adjustment of turns of idling and delay turns
      turbocharger - the description and precautions
      Removal and installation турбокомпрессора
      Survey and service турбокомпрессора
      Removal and installation интеркулера (models with turbocharger)
      The general description and replacement of components of final system
   + Systems of decrease in toxicity of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes
3bf7a351




Removal and installation of the inlet pipeline and final collector

At installation use a new lining.

MODELS WITHOUT ТУРБОКОМПРЕССОРА

 REMOVAL

1. Collectors fasten the same nuts.
2. To facilitate access, turn away bolts of fastening and remove strengthening core where is available, between domes of racks of a forward suspension bracket. Also поддомкратьте a forward part of the car also establish on axial props. Where is available, remove the bottom guard of the engine.
3. Notice a site скоб fastenings of electroconducting or hoses on collectors, and remove them.
4. Loosen the fixing скобу also disconnect an inlet air line from the inlet pipeline.
5. Where it is applied, disconnect hoses from an oil separator established on the inlet pipeline. If it is required, an oil separator it is possible to turn on from an arm.
6. Where it is applied, disconnect hoses сапуна from the inlet pipeline.
7. On the models equipped with system recycling of fulfilled gases, remove the valve and a tube as it is described in the Part From the current Chapter.
8. Separate a reception pipe from a final collector, address to Section the General description and replacement of components of final system.
9. Gradually turn away a nut, fastening inlet and final collectors, and separate collectors from a head of the block of cylinders. Clean a collector lining.


 INSTALLATION

1. Make installation in return sequence, paying attention to the following.
a) Be convinced that contact surfaces of a head of the block of cylinders and a collector pure, and use a new lining. Tighten all fixing details the effort resulted in Specifications.
b) Connect a forward part of final system to a collector, address to Section the General description and replacement of components of final system.
Where it is applied, establish the valve recycling the fulfilled gases in a tube as it is described in Systems of decrease in toxicity of the fulfilled gases of the current Chapter.
d) Place all скобы fastenings of electroconducting or hoses how it has been noted before removal.

MODELS WITH ТУРБОКОМПРЕССОРОМ

 REMOVAL

1. Collectors though also separate, but fasten the same nuts.
2. To facilitate access, turn away strengthening core between domes of racks of a forward suspension bracket. Also поддомкратьте a forward part of the car also establish on axial props. Where is available, remove the bottom guard of the engine.
3. Notice a site скоб fastenings of electroconducting or the hoses attached to collectors, and remove them.
4. Disconnect hoses сапуна from the inlet pipeline, having remembered their arrangement to simplify installation.
5. Remove турбокомпрессор as Removal and installation турбокомпрессора is described in Section.
6. On the models equipped with system recycling of fulfilled gases, remove the valve and a tube as it is described in Systems of decrease in toxicity of the fulfilled gases.
7. Turn away a cable of weight of the engine from an assembly eye on the right end of the inlet pipeline, then turn away an arm from the pipeline.

8. Gradually turn away a nut, fastening inlet and final collectors, and separate collectors from a head of the block of cylinders. Clean a collector lining (address to an accompanying illustration).


 INSTALLATION

1. Make installation in return sequence, paying attention to the following.
a) Be convinced that contact surfaces of a head of the block of cylinders and a collector pure, and use a new lining. Tighten all fixing details the effort resulted in Specifications.
b) Where it is applied, establish the valve recycling the fulfilled gases and a tube as it is described in Systems of decrease in toxicity of the fulfilled gases.
Establish турбокомпрессор as Removal and installation турбокомпрессора is described in Section.
d) Be convinced that hoses сапуна are correctly connected, as has been noted before removal.
e) Place all скобы fastenings of electroconducting or hoses how it has been noted before removal.