Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
- Engine repair
+ Repair of petrol engines of 1.4 l and 1.6 l in an impellent compartment
+ Repair of petrol engines of 2.0 l in an impellent compartment
+ Repair of the diesel engine in an impellent compartment
- Procedures of removal and engine major repairs
Methods of removal of the engine and precaution
Removal and installation of the petrol engine and manual transmission
Removal and installation of the petrol engine and automatic transmission
Removal and installation of the diesel engine and transmission
Sequence of dismantling - an engine partition
Dismantling of a head of the block of cylinders
Cleaning, survey and service of a head of the block of cylinders and valves
Assemblage of a head of the block of cylinders
Removal, check of a condition and installation of a flywheel/privodnogo of a disk
Replacement left (the flywheel/privodnogo of a disk located from outside) an epiploon of a cranked shaft
Removal and pallet installation картера (only for petrol engines of series К7М with the aluminium pallet)
Removal and installation of an intermediate shaft
Removal of assemblage of pistons/rods
Removal коленвала
Cleaning and survey of the block of cylinders/kartera and cylinders
Survey and assemblage of assemblages of pistons/rods
Survey коленвала
Survey of radical bearings
Balance of assembly - an engine partition
Check of a working backlash of radical bearings and installation коленвала
Check of a working backlash шатунных bearings and installation - assemblages of pistons/rods
Start of the engine after a partition
+ System of cooling, heating
+ Power supply systems, release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes
|
Sequence of dismantling - an engine partition
Will work much easier if to establish the engine on a special portable bed. Before to establish the engine on a bed, remove a flywheel/privodnoj a disk that village bolts could be screwed in the block of cylinders.
If the bed is not accessible, it is possible to disassemble the engine on a strong workbench or on a floor. Be extremely cautious, do not overturn and do not drop the engine, working without a bed.
Before to assort the engine or to replace it with already restored block, remove all external components:
|
|
|
a) the Generator and arms.
b) the Distributor (where it is applied), high voltage and spark plug wires (sm of the Head Maintenance service).
The Thermostat and cover (address to the Head System of cooling, heating).
d) the Equipment of system of injection of fuel.
e) the Inlet pipeline and a final collector.
f) the Oil filter.
|
|
g) engine Support, elevating eyes and arms of fastening of hoses (address to an accompanying illustration). |
|
|
h) Auxiliary arms (the pump of the amplifier of a steering, the compressor of the conditioner of air (address to an accompanying illustration). |
|
|
i) On engine K7M turn away a bolt. |
|
|
j) the Pipe маслозаливного apertures and probe level measurements (address to illustrations). |
|
|
k) Remove a sealing ring. |
|
|
l) Tubes and hoses of system of cooling (address to illustrations). |
m) the Flywheel/privodnoj a disk. |
|
DIESEL MODELS
|
|
|
a) a generator Arm.
b) the Fuel pump of a high pressure and its arm, fuel atomizers and candles накаливания.
The Thermostat and cover (address to the Head System of cooling, heating).
d) Turbokompressor (where it is applied - address to the Head of the Power supply system and release).
e) the Inlet pipeline and a final collector (address to the Head of the Power supply system and release).
f) an oil Cooler.
g) engine Support, elevating eyes and arms of fastening of hoses.
h) Auxiliary arms (the pump of the amplifier of a steering, the compressor of the conditioner of air).
i) the Switch of a control lamp of pressure of oil and the gauge of level of oil (where it is applied) (Address to the Head an engine Electric equipment).
j) Gauges of temperature of a cooling liquid (address to the Head System of cooling, heating).
k) Plaits of wires and their arms.
l) Tubes and hoses of system of cooling (address to the Head System of cooling, heating).
m) the Pipe маслозаливного apertures and probe level measurements.
n) Coupling (address to the Head Coupling). |
|
|
|
At removal of external components from the engine, give particular attention to details which can be useful or important at installation. Notice a correct arrangement of linings, consolidations, распорных linings, pins, washers, bolts and other small components. |
If for replacement "the incomplete" engine is got (i.e. assemblage of the block of cylinders, коленвала, pistons and rods), it is necessary to remove from the old engine a head of the block of cylinders, the pallet, the oil pump and gear приводной a belt.
If you plan a full partition, the engine it is possible to disassemble and remove internal components in a following order:
|
|
|
a) the Inlet pipeline and a final collector.
|
|
b) Gear приводной a belt and pulleys, and the water pump (address to an accompanying illustration). |
|
|
Head of the block of cylinders (address to an accompanying illustration). |
d) the Flywheel/privodnoj a disk.
e) the Pallet.
f) the Oil pump.
g) Pistons.
h) Kolenval. |
|
Before the work beginning be convinced that near at hand there are all necessary tools. |
|
