Renault Megane, Scenic

Since 1996 of release

Repair and car operation

Removal and pallet installation картера

For performance of this procedure it is required лебедка. On models with the aluminium pallet (usually), assemblage of the engine and transmission it is necessary to remove engine K7M from an impellent compartment completely.

ENGINE E7J

REMOVAL

1 Disconnect a cable of weight from the battery. If the autoradio tape recorder in your car is coded before to disconnect the battery, be convinced that you know a code. 2. Merge impellent oil, operating according to the description in the Head Maintenance service, then establish and tighten, using a new washer. 3. Поддомкратьте a forward part of the car also establish on axial props. Remove the right forward wheel. 4. Remove a reception pipe and каталитический the converter, operating according to the description in the Head the Suspension bracket and a steering. 5. Disconnect a tip of cross-section steering draught from the lever on a rotary fist as it is described in the Head the Suspension bracket and a steering. 6. Turn away the top bolt, крепящий the right rack of a suspension bracket to a rotary fist. Pay attention that on the brink of a bolt head there are grooves, and a bolt after отворачивания nuts it is necessary to beat out. 7. Loosen the only the bottom bolt, крепящий a rack to a rotary fist. 8. By means of approaching выколотки beat out a cylindrical pin, крепящий the right power shaft to a target shaft of transmission. Incline a rotary fist while will release a power shaft from grooves on a target shaft. Tie up a power shaft to the steering mechanism. 9. Turn away bolts of fastening of the engine to an arm to flywheel transmission/cover. 10. Turn on two nuts, fastening forward support of the engine to a stretcher, and clean распорную a lining from the right support. 11. In a back part of the engine, turn on and remove nuts of bolts, крепящих an arm of a back support of the engine to transmission, and nuts of coupling bolts of a back support. Do not remove bolts at this stage. 12. Remove the air filter as it is described in the Head of the Power supply system, release. 13. Attach лебедку to the engine, using assembly eyes. Alternatively use the basic beam located across an impellent compartment. 14. Disconnect a hose of a coal adsorber from the electromagnetic valve on the inlet pipeline. 15. Release submitting and returnable fuel hoses from the inlet pipeline and боковины frames. 16. Turn away the tank of hydrosystem of the amplifier of a steering, and displace it aside. Do not disconnect hoses. 17. Disconnect the gauge of a speedometer from transmission, putting forward fixing скобу. 18. Accurately lift engine and transmission assemblage that it was possible to remove bolts of a back support and an arm. 19. Continue to lift assemblage until begins to disconnect probably tubes of hydrosystem of a steering with the amplifier from holders on a stretcher. 20. Lift assemblage while the backlash between a bottom edge of the block of cylinders and a stretcher does not become equal 25 see Before pallet removal be convinced that engine/transmission assemblage is reliably supported. 21. Turn away bolts of fastening of the engine to an arm to flywheel transmission/cover under the pallet, then turn away bolts, fastening the pallet to the block of cylinders, but leave two диагонально an opposite bolt, yet do not separate the pallet from the block of cylinders (address to an accompanying illustration). 22. With the help шпателя separate the pallet from the basis of the block of cylinders. Do not use a screw-driver as it can damage contact surfaces. 23. Turn away two remained bolts, and lower the pallet. At first it is necessary to lower it, then to displace to transmission and to take (address to an accompanying illustration). 24. Remove rubber consolidations from flutes in covers of the right and left radical bearings коленвала, or from the bent parts on the pallet ends. Clear the block of cylinders and the pallet of hermetic and wipe them dry.

INSTALLATION

1. Put on combined surfaces of the pallet hermetic in width of 3 mm, having convinced, leading round all apertures under bolts. Renault recommends Rhodorseal 5661. 2. Place new rubber consolidations in flutes in covers of the right and left radical bearings коленвала. Pay attention that strips various. 3. Put the pallet to the block of cylinders and insert bolts. Gradually in diagonal sequence tighten bolts the effort resulted in Specifications. 4. Lower engine/transmission assemblage so that it was possible to attach tubes of hydrosystem of a steering with the amplifier to holders on a stretcher. 5. Lower assemblage and establish bolts of a back support and an arm. Place racks of forward fastening in a stretcher and completely lower assemblage. Disconnect лебедку from the engine. 6. Establish nuts on bolts of forward and back support and tighten their effort resulted in Specifications. 7. Establish the speedometer gauge on transmission and fix it скобой. 8. Establish into place the tank of hydrosystem of the amplifier of a steering and tighten bolts. 9. Attach submitting and returnable fuel hoses to the inlet pipeline and sidewall frames. 10. Connect a hose of a coal adsorber to the inlet pipeline. 11. Establish the air filter, operating according to the description in the Head of the Power supply system, release. 12. Establish and tighten bolts of fastening of the engine to an arm to flywheel transmission/cover. 13. Put the right power shaft to a target shaft of transmission so that apertures of a cylindrical pin have been correctly levelled. Move a power shaft and simultaneously push a rotary fist. Drive into place an external part of a cylindrical pin by means of approaching выколотки, then drive an internal part. Isolate both ends of a cylindrical pin suitable hermetic to prevent water and dirt hit. 14. Insert the top bolt, крепящий the right rack of a suspension bracket to a rotary fist, then tighten the top and bottom nuts the effort resulted in Specifications. Bolts heads should be turned to a forward part of the car. 15. Establish a tip of cross-section steering draught on the lever of a rotary fist, operating according to the description in the Head the Suspension bracket and a steering. 16. Establish a reception pipe and каталитический the converter, operating according to the description in the Head of the Power supply system, release. 17. Establish the right forward wheel and lower the car on the earth. 18. Fill the engine with oil as Maintenance service is described in the Head. 19. Attach a weight cable to the battery.

ENGINE K7M WITH THE PALLET FROM THE STAMPED STEEL

REMOVAL

1 Disconnect a cable of weight from the battery. If the autoradio tape recorder in your car is coded before to disconnect the battery, be convinced that you know a code. 2. Merge impellent oil as Maintenance service is described in the Head, then establish and tighten a drain stopper, using a new washer. 3. Поддомкратьте a forward part of the car also establish on axial props. Remove both lobbies of a wheel. 4. Merge a liquid from cooling system as Maintenance service is described in the Head. 5. Loosen the скобу also disconnect the top hose of a radiator from a thermostat casing. 6. Remove скобы and screws of fastening and remove loose leaves of an arch of the right forward wheel 7. Disconnect conducting of the gauge of oxygen, then remove каталитический the converter and a forward reception pipe of the muffler/converter as it is described in the Head of the Power supply system, release. 8. Note position of the main rod of a choice of transfers on a forward plug in transmission, then ослабьте a coupling bolt and separate two parts of a rod. 9. Disconnect a tip of cross-section steering draught from the lever of the left rotary fist as it is described in the Head the Suspension bracket and a steering. 10. Turn away three bolts, fastening an internal protective cover of the left power shaft to transmission. 11. Turn away both bolts, fastening the left rack of a suspension bracket to a rotary fist. Pay attention that on the brink of a bolt head there are grooves, and a bolt after отворачивания nuts it is necessary to beat out. 12. Accurately separate internally connection of the left power shaft from transmission. Tie up a power shaft aside. 13. Turn away the top bolt, крепящий the right rack of a suspension bracket to a rotary fist. Pay attention that on a bolt head there are grooves, and after removal of a nut the bolt is necessary for beating out. 14. Loosen the (do not remove) the bottom bolt, крепящий a rack to a rotary fist. 15. By means of approaching выколотки beat out a cylindrical pin, крепящий the right power shaft to a target shaft of transmission. Incline a rotary fist while will release a power shaft from grooves on a target shaft. Tie up a power shaft to the steering mechanism. 16. Turn away bolts of fastening of the engine to an arm to flywheel transmission/cover. 17. On the forward party of a stretcher turn away a nut from forward support of the engine and clean a plate from the right support. 18. On a back part of the engine, turn on and remove nuts from bolts, крепящих an arm of a back support of the engine to transmission and nuts of a coupling bolt of a back support. Do not remove bolts at this stage. 19. Turn away bolts and remove strengthening core between domes of a rack of a forward suspension bracket. 20. Turn away a cable of weight on the right side of a partition. 21. Take spring скобу and remove the gauge of a speedometer from a back part of transmission. 22. Turn away bolts or separate the tank of a steering with the amplifier from the engine and place it on the engine. Disconnect a hose of the vacuum amplifier of a brake from the inlet pipeline. 23. Disconnect a hose of a coal adsorber from the inlet pipeline. 24. Where it is necessary, disconnect a ventilation hose картера. 25. Disconnect conducting from a potentiometer throttle заслонки. 26. Disconnect submitting and returnable fuel hoses from a regulator of pressure of fuel and a fuel highway. Address to the Head of the Power supply system, release if it is necessary. 27. Attach лебедку to engine and transmission assemblage and slightly raise the engine. 28. Where it is applied, release a coupling rope in an impellent compartment. 29. Accurately lift engine and transmission assemblage so that it was possible to remove bolts of a back support and an arm. 30. Continue to lift assemblage until begins possible to let out from holders on a stretcher of a tube of hydrosystem of a steering with the amplifier. 31. Lift assemblage while between a bottom edge of the block of cylinders and a stretcher there will be no backlash 26 see Track, that engine electroconducting has not been clamped between transmission and боковиной frames. 32. Turn away bolts, fastening the pallet to the block of cylinders, but leave two диагонально an opposite bolt, the pallet (address to an accompanying illustration) will not be separated yet. 33. With the help шпателя separate the pallet from the basis of the block of cylinders. Do not use a screw-driver as it can damage contact surfaces. 34. Turn away two remained bolts and lower the pallet. At first it is necessary to lower it, then to displace to transmission and to take (address to an accompanying illustration). 35. Remove rubber consolidations from flutes in covers of the left radical bearing. 36. Remove rubber consolidations from flutes in covers of the right radical bearing коленвала or from the bent parts on the pallet ends. Clear the block of cylinders and the pallet of hermetic and wipe them dry (address to illustrations).

INSTALLATION

1. Put on combined surfaces of the pallet hermetic in width of 3 mm, having convinced, leading round all apertures under bolts. Renault recommends Rhodorseal 5661 (see an illustration). 2. Place new rubber consolidations in flutes in covers of the right and left radical bearings коленвала. Pay attention that strips various. 3. Put the pallet to the block of cylinders and insert bolts. Gradually in diagonal sequence tighten bolts the effort resulted in Specifications. 4. Lower engine/transmission assemblage so that it was possible to attach tubes of hydrosystem of a steering with the amplifier to holders on a stretcher. 5. Lower assemblage and establish bolts of a back support and an arm. Place racks of forward fastening in a stretcher and completely lower assemblage. Disconnect лебедку from the engine. 6. Establish nuts on bolts of forward and back support and tighten their effort resulted in Specifications. 7. Where it is necessary, fix a coupling rope in an impellent compartment. 8. Connect submitting and returnable fuel hoses to a regulator of pressure of fuel and a fuel highway and tighten скобы. 9. Connect electroconducting to a potentiometer throttle заслонки. 10. Connect a ventilation hose картера. 11. Connect a hose of a coal adsorber and a hose of the vacuum amplifier of a brake to the inlet pipeline and tighten скобы. 12. Establish the bull-calfe of hydrosystem of the amplifier of a steering and tighten bolts. 13. Establish the speedometer gauge on transmission and fix it скобой. 14. Fix a weight cable to the right party of a partition. 15. Establish strengthening core on куполы racks and tighten bolts. 16. Establish nuts on bolts of forward and back support and tighten their effort of an inhaling regulated by Specifications. 17. Establish and tighten bolts of fastening of the engine to an arm to flywheel transmission/cover. 18. Put the right power shaft to a target shaft of transmission so that apertures of a cylindrical pin have been correctly levelled. Move a power shaft and simultaneously push a rotary fist. Drive into place an external part of a cylindrical pin by means of approaching выколотки, then drive an internal part. Isolate both ends of a cylindrical pin suitable hermetic to prevent water and dirt hit. 19. Insert the top bolt, крепящий the right rack of a suspension bracket to a rotary fist, then tighten the top and bottom nuts the effort resulted in Specifications. Bolts heads should be turned to a forward part of the car. 20. Put internal connection of the left power shaft to transmission, then establish bolts, fastening the left rack of a suspension bracket to a rotary fist. Bolts heads should be turned to a forward part of the car. Tighten nuts the effort resulted in Specifications. 21. Establish three bolts, fastening an internal protective cover of the left power shaft to transmission and tighten its effort resulted in Specifications. 22. Establish a tip of cross-section steering draught on the lever of a rotary fist, operating according to the description in the Head the Suspension bracket and a steering. 23. Establish the main rod of a choice of transfers on a forward plug in transmission, then tighten a coupling bolt the effort resulted in Specifications. 24. Establish каталитический the converter and a reception pipe as it is described in the Head of the Power supply system, release and connect conducting of the gauge of oxygen. 25. Establish loose leaves of an arch of the right forward wheel. 26. Attach the top hose to a thermostat casing. 27. Establish forward wheels and lower the car on the earth. 28. Attach a weight cable to the battery. 29. Fill the engine with oil (address to the Head Maintenance service). 30. Fill cooling system (address to the Head Maintenance service).

ENGINE K7M WITH THE ALUMINIUM PALLET

REMOVAL

1. Remove assemblage of the engine and transmission from the car. 2. Turn away bolts, fastening the pallet to a side of cylinders and separate the pallet from the basis of the block of cylinders. Do not use a screw-driver as can damage contact surfaces. 3. Get the pallet, then remove rubber consolidations from flutes in covers of the right and left radical bearings коленвала, or from the bent parts on each end of the pallet. Clear the block of cylinders and the pallet of hermetic and wipe them dry.

INSTALLATION

1. Put on combined surfaces of the pallet hermetic in width of 3 mm, having convinced, leading round all apertures under bolts. Renault recommends Rhodorseal 5661. 2. Place new rubber consolidations in flutes in covers of the right and left radical bearings коленвала. Pay attention that strips various. 3. Put the pallet to the block of cylinders and insert bolts. Gradually in diagonal sequence tighten bolts the effort resulted in Specifications. 4. Establish engine/transmission assemblage in the car.