Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
- Engine repair
- Repair of petrol engines of 1.4 l and 1.6 l in an impellent compartment
Compression check - the description
Arrangement of the top dead point (ВМТ) the piston №1
Check and adjustment of backlashes of valves
Removal, survey and installation gear drive a belt
Removal, survey and cogwheel installation drive a belt and the tension mechanism
Replacement of an epiploon of a cam-shaft
Removal, survey and cam-shaft installation
Removal, survey and installation of a head of the block of cylinders
Removal and pallet installation картера
Removal, survey and installation of the oil pump and cogwheel
Replacement of epiploons коленвала
Survey and replacement of support of the engine/transmission
Removal, survey and installation of a flywheel/privodnogo of a disk
+ Repair of petrol engines of 2.0 l in an impellent compartment
+ Repair of the diesel engine in an impellent compartment
+ Procedures of removal and engine major repairs
+ System of cooling, heating
+ Power supply systems, release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes
|
Survey and replacement of support of the engine/transmission
The inhaling moments (in Nanometer) engine arms / a manual transmission
The inhaling moments (in Nanometer) engine arms / automatic transmission
|
|
|
1. Cock a manual brake, then поддомкратьте a forward part of the car and establish it on axial props. Where is available, remove the bottom guard of an impellent compartment.
2. Visually examine rubber pillows on two lobbies and one back arms of fastening of the engine/transmission on presence of cracks and pollution. |
|
The right forward fastening
|
|
|
1. Cock a manual brake, then поддомкратьте a forward part of the car and establish it on axial props.
|
|
2. Turn away a nut, крепящую the bottom rack of a support to a stretcher and remove a connecting plate (address to an accompanying illustration). |
3. Turn on two top nuts, fastening a support to an arm.
4. With the help лебедки or a jack and wooden бруска lift the right end of the engine so that it was possible to remove a support.
5. If it is necessary, an arm it is possible to turn on from the block of cylinders. On engine E7J clean распорную a lining from the top bolt. On models with the steering amplifier before arm removal it is necessary to remove the pump of the amplifier of a steering.
6. Establish a new support, operating in an order, the return to removal, tighten nuts/bolts the moment of the inhaling regulated by Specifications (address to illustrations). |
|
The left forward fastening
|
|
|
1. Cock a manual brake, then поддомкратьте a forward part of the car and establish it on axial props.
|
|
2. Turn on and remove the bottom nut, крепящую a support to a stretcher. Watch that the nut has not dropped out in a stretcher (address to an accompanying illustration). |
3. Turn on and remove the top nut, крепящую a support to a transmission arm.
4. With the help лебедки or a jack and wooden бруска lift the left end of the engine/transmission so that it was possible to remove a support.
5. If it is necessary, turn away an arm from transmission.
6. Establish a new support, operating in the return to removal an order, tighten nuts/bolts the effort resulted in Specifications. |
|
Back support
|
|
|
1. For access improvement, cock a manual brake, then поддомкратьте a forward part of the car and establish it on axial props.
2. On engine K7M remove assemblage of the air filter as it is described in the Head of the Power supply system, release.
|
|
3. Working in an impellent compartment, below on the left side of the engine turn away a nut from bolts, крепящих an arm of a back support to transmission (address to an accompanying illustration). |
4. With the help лебедки or a jack and wooden бруска slightly raise the engine.
5. Take bolts and separate an arm from transmission.
|
|
6. Turn away bolts and remove a support from a stretcher (address to an accompanying illustration). |
7. Establish a new support, operating in the return to removal an order, tighten bolts the effort resulted in Specifications. |
|
|
|
