Renault Megane, Scenic

Since 1996 of release

Repair and car operation

Engine/transmission support - survey and replacement

SURVEY

1. Cock a manual brake, then поддомкратьте a forward part of the car and establish it on axial props. Where is available, remove the bottom guard of the engine. 2. Check up a condition of a rubber pillow that there were no cracks, hardenings or отслоения rubbers from a metal basis; replace a support if there are noted damages or pollution. 3. Be convinced that fixing details of a support are reliably clamped; use динамометрический a key to check up the inhaling moments. 4. The big screw-driver or a breakage check up presence of signs of deterioration in a support, accurately wringing out it aside. Where it is possible, ask the assistant to move the engine/transmission back and forth, or here and there, observing of behaviour of a support. If is available excessive люфт, at first check up, that all fixing details have been correctly clamped, and only then replace all worn out components as it is described more low.

FORWARD RIGHT SUPPORT

The inhaling moments (in Nanometer) engine/transmission support - engines F3R

And — Tighten a hairpin the moment of 60 Nanometers In — Tighten a nut the moment of 40 Nanometers

The inhaling moments (in Nanometer) engine/transmission support - engines F7R

* Concerns a nut under a rubber pillow

REPLACEMENT

1. Disconnect a cable of weight from the battery (address to the Head an engine Electric equipment). If the autoradio tape recorder in your car is coded before to disconnect the battery be convinced that at you know a code. 2. Prop up the engine a jack, having laid between them a board piece (remove the bottom guard to facilitate access to the pallet). Lift a jack to transfer on it engine weight. 3. Remove an assembly cover, then turn away three bolts, fastening the top arm of the right support of the engine to the main arm on the block of cylinders. Remove a nut, крепящую the top arm to assemblage of the terminator of movement / to a rubber pillow on a body and remove the top arm. 4. Turn away three bolts of fastening and remove assemblage of the terminator of movement / a rubber pillow from a body. If it is necessary, turn away the main arm and a basic rack and remove them from the end of the block of cylinders. 5. Attentively check up all components on presence of damages and signs of deterioration and replace them where it is necessary. 6. At assemblage, establish the main arm and a basic rack (where it is removed) on the block of cylinders and tighten fastening bolts the effort resulted in Specifications (address to illustrations above). 7. Attach assemblage of the terminator of movement / a rubber pillow to a body, but do not clamp completely fastening bolts. 8. Establish the top arm and tighten bolts, fastening it to the main arm, the effort resulted in Specifications. Now assemblage of the terminator of movement / a rubber pillow it is necessary отцентровать before to clamp fixing bolts. Technicians Renault use special doubled capture Mot. 1289-03 which is inserted through grooves into arms. If this tool is not accessible, it can be made of metal strips. Having centered a support, tighten its fastenings by the effort resulted in Specifications. 9. Clean a jack from under the engine and attach a weight cable to the battery.

FORWARD LEFT SUPPORT

REPLACEMENT

1. Place a jack under transmission, having laid between them a board piece. Lift a jack to transfer on it transmission weight. 2. Turn away the central nut and two bolts of fastening of a rubber pillow and remove a support. 3. If it is necessary, turn away bolts of fastening of a rubber pillow and remove an arm of a support from the top part картера transmissions. 4. Attentively check up all components on presence of damages and signs of deterioration and replace them where it is necessary. 5. Establish a hairpin in an arm of a support and tighten its effort resulted in Specifications - address to illustrations above. 6. Establish an arm on transmission, clamping fixing bolts the effort resulted in Specifications. 7. Establish a rubber pillow on an arm and tighten bolts of fastening and the central nut the effort resulted in Specifications. 8. Clean a jack from under transmission.

BACK SUPPORT

REPLACEMENT

1. If it is not executed yet, cock a manual brake, then поддомкратьте a forward part of the car and reliably establish it on axial props. 2. Prop up the pallet a jack, having laid between them a board piece. Lift a jack to transfer on it engine weight. 3. Turn away a nut and a bolt from each end of assembly communication and remove communication from under the car. If it is necessary, turn away fixing nuts and bolts and remove an arm of a support and a basic bar from the engine/transmission. 4. Attentively check up all components on presence of damages and signs of deterioration and replace them where it is necessary. 5. At assemblage, establish a support arm on a back part of transmission and tighten fastening bolts the effort resulted in Specifications - address to illustrations above. Establish a basic bar. 6. Will establish assembly connection and tighten both bolts the effort resulted in Specifications. 7. Lower the car on the earth.