Renault Megane, Scenic

Since 1996 of release

Repair and car operation

Removal and pallet installation

For performance of this procedure it is required лебедка for an engine raising. At installation use a new lining of the pallet or suitable hermetic.

ENGINES F3R

REMOVAL

1. Disconnect a cable of weight from the battery (address to the Head an engine Electric equipment). 2. Merge impellent oil, then establish and tighten a drain stopper, using a new washer. 3. Поддомкратьте a forward part of the car also establish on axial props. Where is available, remove the bottom guard of the engine. 4. Uncover the right support of the engine. 5. With the help лебедки support engine/transmission weight. 6. Turn away bolts, fastening a reception pipe of the muffler/converter to a final collector. Separate a reception pipe and support it. 7. Turn away strengthening arm-cover of a flywheel/privodnogo of a disk. Pay attention that one of bolts крепит an arm of a back support to transmission and that for отворачивания bolts, крепящих an arm to the engine, is required a face figured key. 8. Turn on holders, fastening a tube of hydrosystem of a steering with the amplifier to the right party of a stretcher. 9. Turn away a nut, крепящую the top arm of the right support of the engine to assemblage of the terminator of movement / a rubber pillow on a body. 10. Lift the engine so to provide enough place for pallet removal. Remember that power shafts and the remained support of the engine remained connected. 11. Turn away bolts, fastening the pallet to the block of cylinders, but leave two диагонально opposite, yet do not separate the pallet from the block of cylinders. 12. With the help шпателя separate the pallet from the basis of the block of cylinders. Do not use a screw-driver as it can damage contact surfaces. 13. Turn away two remained bolts and lower the pallet. Remove a lining where is available. 14. Clear the block of cylinders and the pallet of the lining or hermetic rests and wipe them dry.

ENGINES F7R

At installation use suitable hermetic (Renault recommends Rhodorseal 5661).

REMOVAL

1. Disconnect a cable of weight from the battery (address to the Head an engine Electric equipment). If the autoradio tape recorder in your car is coded before to disconnect the battery be convinced that at you know a code. 2. Merge impellent oil, then establish and tighten a drain stopper, using a new washer. 3. Поддомкратьте a forward part of the car also establish on axial props. Where is available, remove the bottom guard of the engine. 4. Remove both lobbies of a wheel and loose leaves from arches of wheels. 5. Turn away stretcher fastening to a body from each party of the car. 6. Establish the steering mechanism in position "directly". Working in an impellent compartment, shift back a rubber sealing ring, then turn on and remove эксцентриковый a bolt, крепящий the basis of a steering column to the steering mechanism, and separate a steering column (address to the Head the Suspension bracket and a steering) from the steering mechanism. On models with a safety pillow it is important not to damage the circular switch of a pillow of safety below a steering wheel. 7. Remove sound signals (address to the Head the Onboard electric equipment). 8. Turn away bolts, fastening a reception pipe of the muffler/converter to a final collector. Separate a reception pipe and support it. 9. Turn on holders, fastening a tube of hydrosystem of a steering with the amplifier to a stretcher. 10. Turn away one bolt of fastening of a stretcher to the bottom, having noticed an arrangement распорных linings and washers, then establish instead of it one special tool Renault № Т.Av.1233-01 In, wrap a core in the bottom and tighten a nut and a washer from a stretcher underside (address to an accompanying illustration). Repeat this procedure with remained bolts. If specified tools Renault are not present, it is possible to use four cores with a carving (10 mm on one end, 12 mm - on other). 11. Cautiously and in regular intervals turn away a nut in stretcher corners so that it has fallen on 55 - 60 mm. 12. Turn away four nuts of fastening of transmission to the engine on the pallet, then turn away a rack (address to an accompanying illustration). 13. Turn away bolts, fastening the pallet to the block of cylinders, but leave two диагонально opposite while the pallet will not be disconnected from the block of cylinders. 14. With the help шпателя separate the pallet from the basis of the block of cylinders. Do not use a screw-driver, it can damage contact surfaces. 15. Turn away two remained bolts and lower the pallet. 16. Clear the block of cylinders and the pallet of hermetic and wipe them dry.

ENGINES F3R

INSTALLATION

1. Clear combined surfaces of the pallet and the block of cylinders. 2. Where it is necessary, arrange a new lining on the pallet or put hermetic Rhodorseal 5661 on a pallet surface. 3. If the lining is not used, it is important to arrange the pallet so that it should not be displaced any more after hermetic will concern the block of cylinders. As directing it is possible to use long bolts or pins. 4. To prevent капание oils from the oil pump and the block of cylinders, wipe these areas before pallet installation. 5. Press the pallet to the block of cylinders, then insert bolts and gradually tighten their effort resulted in Specifications. 6. Lower the engine, then establish and tighten a nut of the right support of the engine. 7. Establish holders for a tube of hydrosystem of a steering with the amplifier. 8. Establish strengthening arm-cover of a flywheel/privodnogo of a disk and tighten fastening bolts. 9. Establish a reception pipe of the muffler/converter and tighten bolts. 10. Disconnect лебедку and establish a cover on the right support of the engine. 11. Connect the accumulator, then lower the car on the earth. 12. Fill the engine with fresh oil.

ENGINES F7R

INSTALLATION

1. Clear combined surfaces of the pallet and the block of cylinders. 2. Put a strip of hermetic in width of 1 mm (Renault recommends Rhodorseal 5661) on a combined surface of the pallet, besides hermetic should be put on an outer side of a flute of the pallet (address to an accompanying illustration). 3. It is important to arrange the pallet so that it should not be displaced any more after hermetic will concern the block of cylinders. As directing it is possible to use long bolts or pins. To prevent капание oils from the oil pump and the block of cylinders, wipe these areas before pallet installation. 4. Press the pallet to the block of cylinders and insert two диагонально an opposite bolt. Tighten these bolts, then screw four racks in картер couplings. Tighten racks, establish on them a nut with a washer. 5. Establish the remained bolts of the pallet. Gradually tighten all bolts in diagonal sequence the effort resulted in Specifications, then tighten four nuts of fastening of transmission to the engine. 6. Lift a stretcher to the bottom, in regular intervals clamping nuts on each core. When the stretcher will be pressed to the bottom, serially remove the tool and establish bolts of its fastening to the bottom. Tighten all four bolts the moment of the inhaling regulated by Specifications (address to the Head the Suspension bracket and a steering). 7. Fix a tube of hydrosystem of a steering with the amplifier holders on a stretcher and tighten bolts. 8. Attach a reception pipe of the muffler/converter and tighten bolts. 9. Establish sound signals (address to the Head the Onboard electric equipment). 10. Address to the Head the Suspension bracket and a steering and attach a steering column to the steering mechanism. Establish эксцентриковый a bolt and tighten its effort resulted in Specifications. 11. Establish stretcher fastenings to a body and reliably tighten bolts. 12. Establish loose leaves of arches of wheels and the bottom guard of the engine if is available. 13. Establish forward wheels and lower the car on the earth. Tighten bolts of wheels the effort resulted in Specifications. 14. Attach a weight cable to the battery. 15. Fill the engine with oil.