Renault Megane, Scenic

Since 1996 of release

Repair and car operation

Replacement of epiploons коленвала

EPIPLOON FROM OUTSIDE ПРИВОДНОГО THE BELT

REPLACEMENT

1. Remove a cogwheel коленвала as Removal, survey and installation of a cogwheel gear drive a belt and the tension mechanism is described in Section. 2. Notice a correct arrangement of an old epiploon, then by means of a screw-driver take it from a casing. Do not damage a surface коленвала, распорной a lining or an epiploon casing. On some models probably it is necessary to remove the bottom internal cover gear drive a belt. In this case remove a gear wheel/roller of an intermediate shaft and a intermediate pulley (address to Section Removal, survey and installation of a cogwheel gear drive a belt and the tension mechanism), and then turn away a cover. 3. Clear a casing of an epiploon and remove наждачной a skin of the tease and roughness which can cause epiploon damage. On late engines F3R 750 and F3R 751 which have separate распорную a lining on the end коленвала, get a lining - if it is worn out in a place which the old epiploon concerned, develop it and establish into place that the new epiploon concerned not worn out area. If распорная the lining is worn excessively out, replace it. 4. Grease sealing edges of a new epiploon and arrange it on the end of a shaft the closed party outside. A hand press an epiploon into a casing, then by means of a nest or a metal pipe hammer in it on preliminary noted depth - work very cautiously not to damage an epiploon edge. If the shaft surface has been strongly developed, hammer a new epiploon into a casing hardly more deeply that the sealing edge concerned not developed area of a shaft. On engines with separate распорной a lining grease it, then put on it on коленвал and accurately enter into an epiploon. 5. Where it is necessary, establish the bottom internal cover drive a belt and establish an intermediate pulley and a gear wheel/roller as Removal, survey and installation of a cogwheel gear drive a belt and the tension mechanism is described in Section. 6. Establish a cogwheel коленвала as Removal, survey and installation of a cogwheel gear drive a belt and the mechanism of a tension and new gear приводной a belt is described in Section as Removal, survey and installation gear drive a belt is described in Section.

EPIPLOON CASING FROM OUTSIDE ПРИВОДНОГО THE BELT

REPLACEMENT

1. Remove gear приводной a belt as Removal, survey and installation gear drive a belt, from a cogwheel коленвала and an intermediate shaft or an intermediate pulley is described in Section, address to Section Removal, survey and installation of a cogwheel gear drive a belt and the tension mechanism. Get segment шпонку from a cut in коленвале, then turn away the bottom internal cover drive a belt from the block of cylinders. 2. Turn away bolts of fastening of a casing of an epiploon to the pallet. 3. Turn away bolts of fastening and accurately separate an epiploon casing, marking adjusting pins about two bottom apertures under bolts. If the lining of the pallet (engines F3R) is damaged, the pallet it is necessary to remove and replace a lining. On engines without an intermediate shaft notice presence directing приводной chains of the oil pump and two adjusting pins. Be convinced that the directing is suitable for the further use and replace it if there are doubts concerning a condition. On engines of late models F3R 750 and F3R 751, notice also presence separate распорной linings on the end коленвала. 4. An epiploon it is necessary to change every time after casing removal. Notice an arrangement of an old epiploon, then by means of a screw-driver take it and rub off a basic surface. Grease external edge of a new epiploon and insert it into a casing the closed party outside. Put a casing on wooden брусок, then by means of a head or a metal pipe drive an epiploon into place. 5. At installation clear combined surfaces of a casing, the pallet and the block of hermetic. Be convinced that directing to a chain (where it is applied) it is correctly established also adjusting pins are on a place in a casing. 6. Put a strip of hermetic in diameter 0.6 - 1.0 mm (Renault recommends CAF 4/60 THIXO or Rhodorseal 5661) for a surface of a lining of a casing, round internal sides of apertures under bolts, and also on a carving of two bolts (the nearest to an epiploon). Watch that hermetic has corked the lubricant channel in the top end of a casing (address to an accompanying illustration). Establish a casing on the block of cylinders in the pallet, in regular intervals clamping bolts. 7. Establish separate распорную a lining (where it is applied) as it is described in paragraph 4 (the EPIPLOON FROM OUTSIDE ПРИВОДНОГО the BELT) above. On all engines, establish segment шпонку in a cut in коленвале, then establish the bottom internal cover drive a belt and reliably tighten fastening bolts. 8. Establish cogwheels коленвала and an intermediate shaft or an intermediate pulley. Then establish new gear приводной a belt, address to Sections Removal, survey and installation of a cogwheel gear drive a belt and the mechanism of a tension and Removal, survey and installation gear drive a belt.

EPIPLOON FROM OUTSIDE THE DISK FLYWHEEL/PRIVODNOGO

REPLACEMENT

1. For replacement of the left epiploon коленвала it is required to remove transmission from an impellent compartment, that it was possible to take coupling (where it is applied) and a flywheel/privodnoj a disk - address to the Head Transmission and the Head Coupling. Remove a flywheel/privodnoj a disk as it is described in Section of the Support of the engine/transmission - survey and replacement of the current Chapter. 2. A screw-driver take an old epiploon. 3. Examine a contact surface with an epiploon on коленвале. If it is rough or on it grooves in area to which the epiploon concerned were formed, the new epiploon will be necessary for establishing on slightly smaller depth. 4. Rub off a contact surface with an epiploon, then dip a new epiploon in oil and put on it on коленвал the closed party outside. 5. By means of a metal tube hammer in an epiploon on noted depth. 6. Establish a flywheel/privodnoj a disk, address to Section of the Support of the engine/transmission - survey and replacement of the current Chapter. Establish coupling as Coupling is described in the Head, then establish assemblage of transmission and attach it to the engine as it is described in a corresponding Part of the Head.