Renault Megane, Scenic

Since 1996 of release

Repair and car operation



Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
+ Engine repair
+ System of cooling, heating
- Power supply systems, release
   - Fuel and an exhaust system - petrol models
      Removal and installation - assemblage of the air filter and inlet air lines
      The general description of a control system in temperature of air (the central injection)
      Removal, installation and adjustment of a rope of a pedal of gas
      Removal and installation of a pedal of an accelerator
      The general description and use unleaded gasoline
      The general description of system of injection of fuel
      Depressurization of system of injection of fuel
      Removal and installation топливоподкачивающего the pump
      Removal and installation of the gauge of a stock of fuel
      Removal and installation of a fuel tank
      Removal and installation of the case of a throttle
      Check and adjustment of system of injection of fuel
      Removal and installation of components of system of the central injection
      Removal and installation of components of system of the distributed injection
      Removal and installation of the inlet pipeline and final collector
      Removal and installation of final system
   + Fuel and exhaust systems - diesel models
   + Systems of decrease in toxicity of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes
3bf7a351




Removal and installation топливоподкачивающего the pump

Before to begin work, the prevention in Section Fuel and an exhaust system - petrol models see.


 REMOVAL

1. Disconnect a cable of weight from the battery (address to the Head the Electric equipment of the engine for models Scenic).

If the autoradio tape recorder in your car is coded before to disconnect the battery, be convinced that you know a code.

2. Remove a back seat or a pillow of a back seat as it is described in the Head the Body to get access to a cover топливоподкачивающего the pump.

3. By means of a screw-driver remove from a floor a plastic cover to get access to the pump (address to an accompanying illustration).

4. Disconnect a socket of electroconducting from топливоподкачивающего the pump and attach a socket to a car body to prevent its falling for a tank (address to an accompanying illustration).

5a. Note an arrangement of fuel hoses; a green hose on a left-hand side - fuel giving in an impellent compartment, and a red hose near to an electroconducting socket - fuel return (arrows on pump top specify a stream direction). Disconnect both hoses from the top part of the pump, then закупорьте the ends of hoses to minimise fuel loss (address to illustrations).

5b. Special tool Renault for a detachment of a fuel hose.

5c. Connections топливоподкачивающего the pump:
1 — an electroconducting Socket;
2 — Clamps;
3 — the Hose of giving of fuel;
4 — the Hose of return of fuel;
5 — the Blocking ring;
In — the Arrow specifies a stream of return of fuel;
F — the Arrow should specify back and to be a parallel longitudinal axis of the car.

6a. Turn away blocking ring and remove it from a tank (address to illustrations).

6b. The self-made tool for removal of a blocking ring топливоподкачивающего the pump.

7a. Accurately take assemblage топливоподкачивающего the pump from a fuel tank, trying not to damage the lever of the gauge of the index of a stock of fuel.

7b. Remove a rubber sealing ring and check up its condition. If the sealing ring is unsuitable to operation, get new (address to illustrations).

8. Pay attention that the gauge of the index of a stock of fuel/toplivopodkachivajushchego of the pump is accessible only as full assemblage - separate components are not on sale.


 INSTALLATION

1. Be convinced that the filter of a reception tube топливоподкачивающего the pump is not littered. Establish a sealing ring on the top part of a fuel tank.
2. Accurately enter pump assemblage into a fuel tank.
3. Combine an arrow on a cover топливоподкачивающего the pump with an arrow on a fuel tank (the arrow should be directed to a back part of the car), then establish blocking ring. Reliably tighten blocking ring, then repeatedly check up, that labels on a cover of the pump and a tank remained combined.

If there is a suitable head, tighten blocking ring the effort resulted in Specifications.

4. Connect submitting and returnable hoses to the top part топливоподкачивающего the pump.
5. Connect electroconducting
6. Connect the accumulator and start the engine. Check up submitting and returnable hoses топливоподкачивающего the pump on leaks.
7. Establish a plastic cover in a pillow of a back seat.