Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
+ Engine repair
+ System of cooling, heating
+ Power supply systems, release
- Engine electric equipment
- Charge and start systems
Short circuit search
Test and accumulator gymnastics
Removal and accumulator installation
Test of system of a charge
Removal, installation and tension drive a generator belt
Removal and generator installation
Check and generator partition
Check of serviceability of system of start
Removal and starter installation
Test and starter partition
Removal and installation of the lock of ignition
Removal and installation of the switch of a control lamp of pressure of oil
Removal and installation of the gauge of level of oil
+ Ignition system - petrol models
+ System of preheat of the diesel engine
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes
|
Removal and generator installation
|
|
|
1. Disconnect a cable of weight from the battery. Loosen the the tension auxiliary drive a belt as is described in the Head Maintenance service and remove приводной a belt from a generator pulley. |
|
|
|
Renault recommends to change приводной a belt after each removal. |
MODELS WITH ENGINES E7J AND К7М
|
|
|
1. Cock a manual brake, then поддомкратьте a forward part of the car and establish it on axial props.
Remove the right wheel, a protective guard картера the engine and the loose leaf of an arch of a wheel.
2. If приводной the belt is subject to replacement, on models without air conditioner, at first remove приводной a belt of a steering with the amplifier as Maintenance service is described in the Head.
|
|
3a. Remove rubber covers (where are available) from generator plugs, then turn away fixing nuts. |
|
|
3b. Disconnect electroconducting from a back part of the generator (address to illustrations). |
4. Loosen the шарнирный and adjusting bolts also turn the generator to the engine. Remove приводной a belt from a pulley.
5. Turn on and remove the top adjusting bolt of the generator.
6. Turn on and remove bottom шарнирный a generator bolt.
7. Disconnect a tip of cross-section steering draught from the right rotary fist as it is described in the Head the Suspension bracket and a steering.
8. On all models except Scenic, turn on and remove the right bolts of the top fastening of a rack of a suspension bracket as it is described in the Head the Suspension bracket and a steering.
9. On Scenic models, remove a bolt, крепящий a forward basic bar of a stretcher to a wing longeron, and also a nut, крепящую it to the forward rotary plug of the bottom lever, and remove a bar. Remove a back basic bar of a stretcher in the same way. Address to the Head the Suspension bracket and a steering and remove two nuts with washers from bolts, крепящих a rotary fist to a suspension bracket rack. Take bolts and prop up fist assemblage.
10. Ask the assistant to lower the right suspension bracket downwards and remove the generator. |
|
MODELS WITH ENGINES F3R
|
|
|
1. Turn away eight bolts, fastening ВВ ignition coils to an arm, and move coils aside. Turn away two top bolts and ослабьте the bottom bolt of an arm of the coil of ignition. Develop an arm downwards to get access to a fixing bolt of the generator.
2. Remove rubber covers (where are available) from generator plugs, then turn away fixing nuts and disconnect electroconducting from a back part of the generator. |
|
MODELS WITH ENGINES F7R
|
|
|
1. Cock a manual brake, then поддомкратьте a forward part of the car and establish it on axial props. Remove the right wheel, the bottom guard of the engine and loose leaves of an arch of a wheel.
2. On models with air conditioner, remove приводной a belt as Maintenance service is described in the Head.
3. Turn away a bolt of the top fastening of the mechanism of a tension and a fixing bolt of an arm of the mechanism of a tension. Remove the tension mechanism, watching to losing a washer established behind a fixing arm.
4. Where it is necessary, remove the tank of hydrosystem of the amplifier of a steering and move it aside.
5. Remove rubber covers (where are available) from generator plugs, then turn away fixing nuts and disconnect electroconducting from a back part of the generator.
6. Turn away fixing bolts and nuts of the generator and remove the block from the engine. |
|
MODELS WITH DIESEL ENGINES
|
|
|
1. Behind the generator, turn away an arm bolt топливопровода and move it aside.
2. If приводной the belt is subject to replacement, поддомкратьте a forward part of the car and establish it on axial props.
3. Remove rubber covers (where are available) from generator plugs, then turn away fixing nuts and disconnect electroconducting from a back part of the generator.
4. Turn on and remove fixing bolts, remove приводной a belt from a pulley, then take the generator from the engine. |
|
|
|
|
1. Make installation in return sequence. |
|
|
|
