Renault Megane, Scenic

Since 1996 of release

Repair and car operation



Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
- Engine repair
   + Repair of petrol engines of 1.4 l and 1.6 l in an impellent compartment
   + Repair of petrol engines of 2.0 l in an impellent compartment
   - Repair of the diesel engine in an impellent compartment
      The description of check of a compression and tightness of connections of components
      Arrangement of the top dead point (ВМТ) for the piston №1
      Check and adjustment of backlashes of valves
      Removal, survey and installation gear drive a belt
      Removal at installation of cogwheels drive a belt and the tension mechanism
      Replacement of epiploons of a cam-shaft
      Removal, survey and installation of a cam-shaft and pushers
      Removal, survey and installation of a head of the block of cylinders
      Removal and pallet installation
      Removal, survey and installation of the oil pump
      Replacement of epiploons коленвала
      Replacement of support of the engine/transmission
      Removal and installation of an oil radiator
      Replacement of an epiploon of an intermediate shaft
      Removal, survey and flywheel installation
   + Procedures of removal and engine major repairs
+ System of cooling, heating
+ Power supply systems, release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes
3bf7a351




Removal and pallet installation

At installation use a new lining of the pallet or suitable hermetic (where it is applied).

 REMOVAL

1. Disconnect a cable of weight from the battery.

If the autoradio tape recorder in your car is coded before to disconnect the battery, be convinced that you know a code.

2. Merge impellent oil, then establish and tighten a drain stopper the effort resulted in Specifications (use a new washer).
3. Поддомкратьте a forward part of the car also establish it on axial props. Where is available, remove the bottom guard of the engine.
4. Turn away strengthening core (where is available) between domes of a forward suspension bracket.
5. On engines F8Q, turn away bolts of fastening and remove the top plastic cover drive a belt / the right support of the engine. On engines F9Q, turn away fixing nuts and remove a sound-proof cover of the engine.
6. With the help лебедки support engine/transmission weight.
7. Turn away bolts, fastening a reception pipe of the muffler/converter to a final collector. Separate a reception pipe and support it.
8. Turn away a flywheel arm/cover. Pay attention that one of bolts крепит an arm of a back support to transmission, and for отворачивания bolts of fastening of an arm to the engine is required a face figured key.
9. Turn on holders, fastening a tube of hydrosystem of a steering with the amplifier to the right party of a stretcher.
10. Turn away a nut, крепящую the top arm of the right support of the engine to assemblage of the terminator of movement / a rubber support of the engine on a body.
11. Lift the engine so that was possible to remove the pallet.
12. Turn away bolts, fastening the pallet to the block of cylinders, but leave two диагонально the opposite.
13. Separate the pallet from the basis of the block of cylinders. Do not use a screw-driver as it can damage contact surfaces.
14. Turn away two remained bolts and lower the pallet. Remove a lining where is available.
15. Clear the block of cylinders and the pallet of the lining or hermetic rests.


 INSTALLATION

1. Check up cleanliness of combined surfaces of the pallet and the block of cylinders.
2. Where is available, arrange a new lining on the pallet, and in the absence of a lining put hermetic in width of 1 mm - Renault recommends Rhodorseal 5661 - on a combined surface of the pallet (on an outer side of a flute of the pallet).
3. If the lining is not used, it is important to arrange the pallet so that it should not be displaced any more after hermetic will concern the block of cylinders. As directing it is possible to use long bolts or pins.
4. To prevent капание oils from the oil pump and the block of cylinders, wipe these areas before pallet installation.
5. Press the pallet to the block of cylinders, then insert bolts and gradually tighten their effort resulted in Specifications.
6. Lower the engine, then establish and tighten a nut of the right support of the engine.
7. Establish holders for a tube of hydrosystem of a steering with the amplifier.
8. Establish strengthening arm-cover of a flywheel/privodnogo of a disk and tighten fastening bolts.
9. Establish a reception pipe of the muffler/converter and tighten bolts.
10. Remove лебедку and establish the top plastic cover drive a belt / the right support of the engine or a sound-proof cover where is available.
11. Where it is applied, establish strengthening core between domes of a forward suspension bracket and tighten bolts.
12. Connect the accumulator, then lower the car on the earth.
13. Fill the engine with fresh oil.